LG ARWN038GA2 Service Manual Download Page 6

Page: 6 / 81

- 6 -

LGE Internal Use Only

CAUTION

■

Installation

Safety Precautions

When the product is soaked (flooded or
submerged), contact an Authorized Service
Center.

• There is risk of fire or electric shock.

Take care to ensure that nobody could step
on or fall onto the outside unit.

• This could result in personal injury and product

damage.

Do not open the inlet grille of the product during operation. (Do not touch the electrostatic fil-
ter, if the unit is so equipped.)

• There is risk of physical injury, electric shock, or product failure.

Always check for gas (refrigerant) leakage
after installation or repair of product.

• Low refrigerant levels may cause failure of

product.

Do not install the product where the noise or
hot air from the outside unit could damage
the neighborhoods.

• It may cause a problem for your neighbors.

Keep level even when installing the product.

• To avoid vibration or water leakage.

Do not install the unit where combustible gas
may leak.

• If the gas leaks and

accumulates around the
unit, an explosion may
result.

90˚

Gasolin

Summary of Contents for ARWN038GA2














































































Search results

Summary of Contents for ARWN038GA2

Reviews:

LG ARWN038GA2, Service Manual, Page: 6 / 81

Search results

Summary of Contents for ARWN038GA2

Reviews: