manualshive.com logo in svg

LG ARWN038GA2, Service Manual, Page: 25 / 81

Share
Download
LG ARWN038GA2 Service Manual Download Page 25

- 25 -

Copyright ©2013 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Function

2) Step 2 : Communication check

- If all model code is displayed in 7-segment communication between outdoor units is normal.
- If 104* is displayed in 7-segment, check communication wires between outside units and Dip switch setting.

3) Step 3 : PCB error check

- After 40sec, error check begins.

4) Step 4 : Auto addressing of indoor units

- Auto addressing begins when address(red) button in Main PCB is pressed for 6sec.
- During auto addressing, 7-segment on main PCB displays "88"
- After auto addressing, the number of indoor units is displayed in 7-segment for 30sec. The address of each

indoor unit is displayed on each wired remote controller.

Push address(red) button for 6sec.

Auto address starts

Auto address is in progress (max. 15min.)

The number of indoor units is displayed for 30sec.

(9 indoor units found)

Auto address process is finished.
Every indoor unit displays its address on 
wired remote controller and the 7segment of 
main PCB is off.

1

2

3

4

5

6

7

ON

1

2

3

4

5

6

7

ON

1

2

3

4

5

6

7

8

9 10 11 12 13 14

6sec.

Summary of Contents for ARWN038GA2


















































































Reviews:

No comments