LevelOne GEL-1061 User Manual Download Page 280 | Manualshive

Page: 280 / 500

background image

Chapter 12

| Security Measures

ARP Inspection

– 280 –

Command Usage

Enabling & Disabling ARP Inspection

◆

ARP Inspection is controlled on a global and VLAN basis.

◆

By default, ARP Inspection is disabled both globally and on all VLANs.

■

If ARP Inspection is globally enabled, then it becomes active only on the
VLANs where it has been enabled.

■

When ARP Inspection is enabled globally, all ARP request and reply packets
on inspection-enabled VLANs are redirected to the CPU and their switching
behavior handled by the ARP Inspection engine.

■

If ARP Inspection is disabled globally, then it becomes inactive for all
VLANs, including those where inspection is enabled.

■

When ARP Inspection is disabled, all ARP request and reply packets will
bypass the ARP Inspection engine and their switching behavior will match
that of all other packets.

■

Disabling and then re-enabling global ARP Inspection will not affect the
ARP Inspection configuration of any VLANs.

■

When ARP Inspection is disabled globally, it is still possible to configure
ARP Inspection for individual VLANs. These configuration changes will only
become active after ARP Inspection is enabled globally again.

◆

The ARP Inspection engine in the current firmware version does not support
ARP Inspection on trunk ports.

Configuring

Global Settings for

ARP Inspection

Use the Security > ARP Inspection (Configure General) page to enable ARP
inspection globally for the switch, to validate address information in each packet,
and configure logging.

Command Usage

ARP Inspection Validation

◆

By default, ARP Inspection Validation is disabled.

◆

Specifying at least one of the following validations enables ARP Inspection
Validation globally. Any combination of the following checks can be active
concurrently.

■

Destination MAC – Checks the destination MAC address in the Ethernet
header against the target MAC address in the ARP body. This check is
performed for ARP responses. When enabled, packets with different MAC
addresses are classified as invalid and are dropped.

«
...
278
279
280
281
282
...
»

Summary of Contents for GEL-1061





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GEL-1061

DUB-H4 - Hub - USB

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: Campbell Hausfeld Pages: 12

Underwater Switch 24V DC/DMX/02

Brand: Oase Pages: 40

Brand: Waters Network Systems Pages: 16

Brand: Edge-Core Pages: 12

Cooper Power Systems LCR 6200 RFN

Brand: Eaton Pages: 8

Brand: Free-Way Switch Pages: 6

Brand: Net Generation Pages: 38

852-1411/000-001

Brand: WAGO Pages: 40

EXT-UHDA-HBTL-RX

Brand: Gefen Pages: 33

Brand: DX Engineering Pages: 4

Brand: SLV Pages: 22

JTECH-4K88-EX-RX

Brand: J-TECH Pages: 40

Brand: Kramer Pages: 4

Brand: Pakedge Device & Software Pages: 8

Brand: Black Box Pages: 2

EG5-0702-SFP Series

Brand: Leonton Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands