Lattice Semiconductor sysCLOCK ECP5 Usage Manual Download Page 39

Page: 39 / 43

ECP5 and ECP5-5G sysCLOCK

PLL/DLL Design and Usage Guide

module PLLREFCS(CLK0, CLK1, SEL, PLLCSOUT);
input CLK0, CLK1, SEL;
output PLLCSOUT;
endmodule;

PLLREFCS Instantiation

PLLREFCS PLLREFCSInst0 (
.CLK0 (CLK_0)
,.CLK1 (CLK_1)
,.SEL (SELECT)
,.PLLCSOUT (CLK_OUT));

Technical Support Assistance

Submit a technical support case through

www.latticesemi.com/techsupport

Revision History

Date

Version

Change Summary

November 2015

1.1

Added support for ECP5-5G.

Changed document title to ECP5 and ECP5-5G sysCLOCK
PLL/DLL Design and Usage Guide.

Updated

Oscillator (OSCG)

section. Removed paragraph on

STDBY port.

Updated

PLL Usage in Clarity Designer

section. Replaced

Figure 30, Clarity Designer Main Window for PLL Module.

Updated

Technical Support Assistance

section.

March 2014

01.0

Initial Release

Summary of Contents for sysCLOCK ECP5












































Search results

Summary of Contents for sysCLOCK ECP5

Reviews:

Related manuals for sysCLOCK ECP5

Brands by name

Popular brands

Lattice Semiconductor sysCLOCK ECP5, Usage Manual

Search results

Summary of Contents for sysCLOCK ECP5

Reviews:

Related manuals for sysCLOCK ECP5

Brands by name

Popular brands