KYMCO ADG5 Manual Download Page 328

Page: 328 / 426

9.Electrical Systems

XCITING S 400

9-28

Luggage Box Light

The lamp lights up when Seat Pad is lifted up, goes out when closed. (The

Cabinet Light is provided with light-sensing switch; in case the user forgets to

close the Seat Pad or the Pad fails to fully close up, system will cut the power

automatically after a set time, preventing any power loss of battery.)

Remove bolts, lift up the luggage box. See the external topic for the details.

Remove the luggage box switches connectors.

Remove the luggage box and switches.

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands