KYMCO ADG5 Manual Download Page 350

Page: 350 / 426

10..Brake System

XCITING S 400

Rear Brake Pad Removal

SAFETY FIRST: Protective gloves and eyewear are recommended at this point.

Warning: Brake fluid is very caustic and can damage paint, chrome and plastic.

Wipe up any spills immediately.

Removal

Place a suitable container under the banjo bolt to catch any remaining

brake fluid. Remove the banjo bolt that holds the brake hose to the

caliper using a 12 mm socket. Discard the two sealing washers.

Remove the rear brake caliper from the rear fork.

Free the parking brake cable from the rear brake caliper.

Remove the brake pad pin plug with a flat blade screwdriver.

10-13

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands