KYMCO ADG5 Manual Download Page 86

Page: 86 / 426

3. Engine > Engine Removal

XCITING 400i

Loosen the water pump hose clamp with a #2 Phillips screwdriver. Slide

up the clamp and free the coolant hose from the water pump. Allow any

remaining coolant to drain into a suitable container.

Loosen the thermostat hose clamp with a #2 Phillips screwdriver. Slide

up the clamp and free the coolant hose from the thermostat. Allow any

remaining coolant to drain into a suitable container.

Squeeze the air bleed hose clamp with needle nose pliers and slide

back the clamp. Free the air bleed hose from the thermostat.

4‐8

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands