KYMCO ADG5 Manual Download Page 26

Page: 26 / 426

2.Periodic Maintenance XCITING S 400

Replenishing Brake Fluid

1. Straighten the Handlebar, remove 2 fixing screws of Reservoir and remove

Reservoir Cover.

2. Replenish Reservoir with recommended DOT-4 Brake Fluid to the Upper Scale.

Replace Reservoir Cover and tighten 2 fixing screws.

3. Replace Brake Fluid every 10000km or 1 year.

WARNING

◆

Mixed use of Brake Fluids of different brand and different specifications

may result in braking fault and danger.

◆

When replenishing braking fluid, cover coated parts with a cloth to

prevent damaging them.

9-6

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands