KYMCO ADG5 Manual Download Page 253

Page: 253 / 426

6.Fuel System

XCITING S 400

6-40

Fuel Injection Diagnostic Tool

OPERATION INSTRUCTIONS

Diagnostic tool Part Number: 3620A-LEB2-E00

This tool has been developed by KYMCO and for KYMCO vehicles only.

The tool software can be updated for new models with a computer via the USB

cable.

Please refer to the specifications when serving this vehicle.

This tool does not have an internal battery. The power for the tool is provided by

the vehicle when connected. The vehicle should have a fully charged battery

when using the diagnostic tool.

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands