KYMCO ADG5 Manual Download Page 405

Page: 405 / 426

13.Rear Suspension

XCITING 400i/XCITING S 400

Check over the shock absorber for damage and oil leaks. Replace the
shock absorber if needed. Do not attempt to disassemble the shock
absorber.

Installation

Fit the shock absorber into place. Make sure the preload arrow
indicator faces out from the lower mount.

Install the upper shock absorbers. Insert the upper mounting bolt first.
Tighten the bolts to specification with a 14 mm socket.

Item

Q'ty Thread dia.(mm)

Torque

Nm (kgf-m, ft-lb)

Rear shock absorber bolt

40 (4, 29)

13-10

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands