KYMCO ADG5 Manual Download Page 45

Page: 45 / 426

2.Periodic Maintenance XCITING S 400

Spark Plug

remove the spark plug wire off of the spark plug.

Remove the connectors of the ignition coil.

Remove the two ignition coil mounting bolts and remove the ignition coil.

Clean off the area surrounding the spark plug with compressed air or a shop towel

to make sure debris doesn't get into the combustion chamber when the spark plug is

removed.

NOTE: Always wear safety glasses when using compressed air and never point it

directly at yourself or anyone else.

Remove the spark plug with a spark plug with a 5/8 in socket.

Spark plug

NGK CR7E

9-25

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands