KYMCO ADG5 Manual Download Page 307

Page: 307 / 426

9.Electrical Systems

XCITING S 400

9-7

• Check the battery condition before performing any inspection that requires

proper battery voltage.

• A continuity test can be made with the switches installed on the scooter.

• Route the wires and cables properly after servicing each component.

TROUBLESHOOTING

Lights do not come on when ignition switch is “ON”

• Burned bulb

• Faulty switch

• Poorly connected, broken or shorted wire

Temperature gauge does not register correctly

• Faulty temperature gauge

• Faulty thermosensor

• Broken or shorted wire between the temperature gauge and thermosensor

Fuel gauge does not work or shows wrong figures

• Faulty fuel gauge

• Faulty fuel unit

• Poorly connected wire between fuel gauge and fuel unit

• Fuse burned out

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands