KYMCO ADG5 Manual Download Page 244

Page: 244 / 426

6.Fuel System

XCITING S 400

6-31

Fuel Injector Removal

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Warning: Gas is extremely flammable! Do not work around an open flame or a

source of sparks.

In order to release fuel pressure from the fuel pipe when removing the fuel

injector, unplug the fuel pump connecter. Start the engine and let it run until it

dies of fuel starvation. Turn the ignition switch off.

Clamp the fuel hose for safety. And loosen the fuel hose clamp.

Inspect the fuel hose for signs of deterioration or damaged. Replace the fuel

hose as needed.

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands