KYMCO ADG5 Manual Download Page 161

Page: 161 / 426

3. Engine > Oil Pump

XCITING 400i

Oil Pump

SAFETY FIRST: Protective gloves and eyewear are recommended at this point.

GENERAL INSTRUCTIONS

The maintenance of lubrication system can be performed with the engine installed in

the frame. Use care when removing and installing the oil pump not to allow dust and

foreign matters to enter the engine and oil line.

Do not attempt to disassemble the oil pump. The oil pump must be replaced as a set

when it reaches its service limit.

After the oil pump is installed, check each part for oil leaks.

TROUBLESHOOTING

Oil level too low
1. Natural oil consumption

2. Oil leaks

3. Worn or poorly installed piston rings

4. Worn valve guide or seal

Poor lubrication pressure
1. Oil level too low

2. Clogged filter or oil passages

3. Not using the specified oil

3‐83

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands