KYMCO ADG5 Manual Download Page 331

Page: 331 / 426

9.Electrical Systems

XCITING S 400

9-31

Incline the tilt switch 65±10 degrees to the left or right at the ignition switch “ON”.

Measure the voltage as below.

Terminal

Standard

Violet/Red (+) ~ Green/Pink (-)

5 V (ECU voltage)

Black/Blue (+) ~ Green/Pink (-)

3.7 - 4.4 V

Note: Repeat this test, first turn the ignition switch to “OFF”, then turn the ignition

switch to “ON”.

Disconnect the connector to remove the tilt switch.

Note: Install the tilt switch with its “up” mark facing up and tighten the two screws

securely.

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands