KYMCO ADG5 Manual Download Page 48

Page: 48 / 426

2.Periodic Maintenance XCITING S 400

Steering Inspection

Raise the front wheel off the ground and check that the steering handlebar rotates

freely. If the handlebar moves unevenly, binds, or has vertical movement, adjust the

steering head bearing. See the Steering Stem Removal topic for more information.

Front Suspension Inspection

Check the action of the front shock absorbers by compressing them several times.

Check the entire shock absorber assembly for oil leaks, looseness or damage.

9-28

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands