KYMCO ADG5 Manual Download Page 351

Page: 351 / 426

10..Brake System

XCITING S 400

Loosen the brake pad pin with a 5 mm Allen.
Remove the brake pad pin with a 5 mm Allen.

Free the brake pads from the pad retainer.
Remove the brake pads.

Replace the pads if the brake wear exceeds the wear indicator lines or if the wear is uneven.
Always replace brake pads as a set.

When installation:

Apply a light coat of waterproof grease to the brake pad pin. Push the pads

against the pad spring.It may be necessary to rotate the piston and force the

pistons back into the caliper in order to allow room for the brake disc to fit

between the new pads.

Install the rear caliper. Guide the brake disc between the pads. Install the two

caliper bracket mounting bolts. Tighten the mounting bolts to specification.

10-14

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands