KYMCO ADG5 Manual Download Page 106

Page: 106 / 426

XCITING 400i

3. Engine > Camshaft

Wipe the rocker arm shafts clean. Insert the rocker arm shafts

through the camshaft holders and rocker arms. Install the rocker

arm shafts so that the end sits as shown.

Install the camshaft set plate so it fits into the groove on the

camshaft and between the projections on the rocker arm shafts.

Apply a small amount of blue Loctite (non-permanent) to the

threads of the set plate bolt. Thread in the bolt and tighten it to

specification with a
5 mm Allen socket.

3‐28

Summary of Contents for ADG5











































































































































































































































































































































































































































Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands

KYMCO ADG5, Manual

Search results

Summary of Contents for ADG5

Reviews:

Related manuals for ADG5

Brands by name

Popular brands