KTM 2011 690 SMC AUS Repair Manual Download

Page: 113 / 229

ENGINE

111

16.3.18 Removing piston

300030-10

–

Take off the cylinder head gasket

–

Remove screw

–

Push the cylinder upward.

Info

Push the cylinder upward only far enough to allow removal of the piston pin.
Ensure that the two grooved pins remain in place.

300031-10

–

Remove piston pin retainer

–

Remove the piston pin.

–

Take off the cylinder with the piston.

–

Push the piston upward out of the cylinder.

Info

If no other work is required on the cylinder and the piston, you can leave the
piston in the cylinder.

–

Take off the cylinder base gasket.

Info

Ensure that the two grooved pins remain in place.

16.3.19 Removing rotor

300044-10

–

Remove special tool

Engine blocking screw (77329010000) (

p. 218)

300040-10

–

Use the special tool to hold the rotor tight.

Holding spanner (75029091000) (

p. 217)

–

Loosen the nut

of the rotor and remove it with the tab washer.

Info

The crankshaft must not be blocked.

302120-10

–

Install the special tool

on the rotor. Hold it tight using the special tool and pull

off the rotor by turning the screw in.

Extractor (58429009000) (

p. 210)

–

Remove the special tool.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands