KTM 2011 690 SMC AUS Repair Manual Download | Manualshive

Page: 82 / 229

background image

13

WIRING HARNESS, BATTERY

80

300199-11

Main work

–

Disconnect the negative (minus) cable

1

of the battery.

Info

Never operate the motorcycle with a discharged battery or without a battery.
In both cases, electrical components can safety equipment can be dam-
aged. The vehicle is therefore no longer roadworthy.

13.4

Connecting the battery

300199-11

Main work

–

Reconnect minus cable

1

.

Finishing work

–

Mount the seat. (

p. 60)

–

Set the clock. (

p. 94)

13.5

Recharging the battery

Warning

Risk of injury

Battery acid and battery gases cause serious chemical burns.

–

Keep batteries out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

Avoid contact with battery acid and battery gases.

–

Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms.

–

In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least
15 minutes and contact a physician.

Warning

Environmental hazard

The battery contains elements that are harmful to the environment.

–

Do not discard batteries with the household waste. Dispose of faulty batteries in an environmentally compatible manner.
Give the battery to your authorized KTM dealer or dispose of it at a collection point for used batteries.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Even when there is no load on the battery, it still loses power steadily.
The charging level and the method of charging are very important for the service life of the battery.
Rapid recharging with a high charging current shortens the battery's service life.
If the charging current, charging voltage and charging time are exceeded, electrolyte escapes through the safety valves. This
reduces the battery capacity.
If the battery is depleted from starting the vehicle repeatedly, the battery must be charged immediately.
If the battery is left in a discharged state for an extended period, it will become over-discharged and sulfate, destroying the
battery.
The battery is maintenance-free, which means that the acid level does not need to be checked.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the seat. (

p. 59)

–

Remove the battery. (

p. 79)

«
...
80
81
82
83
84
...
»

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Related manuals for 2011 690 SMC AUS

Indian eFTR Mini 2021

Brand: Razor Pages: 20

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: LAZER Pages: 19

Brand: Kong Pages: 72

Brand: R&G Pages: 21

Brand: Malossi Pages: 36

Brand: Wedze Pages: 63

Brand: Biltema Pages: 2

Brand: kellermann Pages: 7

Brand: DYNATEK Pages: 13

990D0-E5500-000

Brand: Suzuki Pages: 10

Brand: Shad Pages: 2

Spyder RS Series

Brand: Can-Am Pages: 37

Brand: APRILIA Pages: 151

BULLET TRIALS 500

Brand: Royal Enfield Pages: 74

HIMALAYAN EURO IV 2017

Brand: Royal Enfield Pages: 294

450 EXC RACING 2006

Brand: KTM Pages: 111

Brand: Caberg Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands