KTM 2011 690 SMC AUS Repair Manual Download

Page: 156 / 229

ENGINE

154

306140-10

–

Remove the special tool.

Engine blocking screw (77329010000) (

p. 218)

–

Mount and tighten screw

with the washer.

Guideline

Screw plug, crankshaft clamp

20 Nm
(14.8 lbf ft)

16.5.22 Adjusting valve clearance

300156-10

–

Remove screws

Info

Make sure that the crankshaft is at top dead center.

300157-10

–

Screw suitable screws

into the rocker arm shafts

. Pull out the rocker arm

shafts.

–

Take off the rocker arm.

300158-10

–

Remove shims

and set them down according to the installation position.

–

Correct the shims as indicated by the results of the valve clearance check.

–

Insert suitable shims.

–

Position the rocker arms and push in the rocker arm shafts.

Info

Make sure that the tapped hole of the rocker arm shaft is positioned facing
outwards.
The small drill hole and the flat surface must point upwards.

300156-11

–

Install and tighten the screws

of the rocker arm shafts.

Guideline

Screw, rocker arm shaft

12 Nm (8.9 lbf ft)

–

Check the valve clearance. (

p. 153)

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands