KTM 2011 690 SMC AUS Repair Manual Download

Page: 173 / 229

IGNITION SYSTEM

171

20.3

Ignition coil - checking the secondary winding

Condition

Ignition coil cylinder 1 is disconnected.
Spark plug connector cylinder 1 has been removed.

Preparatory work

–

Remove the seat. (

p. 59)

–

Remove the fuel tank.

600739-13

Main work
Ignition coil cylinder 1 - check the secondary winding resistance

–

Measure the resistance between the specified points.
Ignition coil pin

2 (+)

–

Ignition coil pin

Ignition coil

Resistance of secondary winding
at: 20 °C (68 °F)

10.4… 15.6 k

Ω

» If the displayed value is not equal to the setpoint value:

–

Replace the ignition coil.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands