KTM 2011 690 SMC AUS Repair Manual Download | Manualshive

Page: 89 / 229

background image

14

BRAKE SYSTEM

87

600603-10

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Check the brake fluid level in the viewer

1

.

» When the brake fluid level drops below the

MIN

mark:

–

Add front brake fluid. (

p. 87)

14.5

Adding front brake fluid

Warning

Danger of accidents

Failure of the brake system.

–

If the brake fluid level falls below the

MIN

mark, this indicates a leakage in the brake system or worn-out brake linings.

Check the brake system and do not continue riding.

Warning

Skin irritation

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Danger of accidents

Reduced braking efficiency due to old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5
brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

Preparatory work

–

Check the front brake linings. (

p. 85)

Main work

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

100254-10

–

Remove screws

1

.

–

Remove cover

2

with membrane

3

.

–

Add brake fluid to level

A

.

Guideline

Measurement of

A

5 mm (0.2 in)

Brake fluid DOT 4 / DOT 5.1 (

p. 206)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilt brake fluid immediately with water.

«
...
87
88
89
90
91
...
»

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Related manuals for 2011 690 SMC AUS

Brand: Cobra Pages: 2

Brand: NZI Helmets Pages: 4

Brand: KSR Moto Pages: 51

Brand: Suzuki Pages: 447

Brand: GAS GAS Pages: 131

Brand: AFX Pages: 112

Brand: Honda Pages: 330

640 LC4 Adventure

Brand: KTM Pages: 59

Brand: DYNATEK Pages: 11

Brand: DYNATEK Pages: 4

Brand: Arai Pages: 15

Brand: Magna Pages: 223

Brand: Benelli Pages: 13

DERBI GPR50-R 1997

Brand: NACIONAL MOTOR Pages: 57

350 EXC-F AUS 2014

Brand: KTM Pages: 24

Brand: Honda Pages: 132

250 EXC-F EU 2010

Brand: KTM Pages: 136

Brand: X-lite Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands