manualshive.com logo in svg

KTM 2011 690 SMC AUS, Repair Manual

Share
Download
KTM 2011 690 SMC AUS Repair Manual Download Page 84

13

WIRING HARNESS, BATTERY

82

13.7

Changing the main fuse

Warning

Fire hazard

 

The electrical system can be overloaded if the wrong fuses are used.

–

Use only fuses with the prescribed amperage. Never by-pass or repair fuses.

Info

The main fuse protects all power consumers in the vehicle. It is in the housing of the starter relay next to the battery.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the seat. (

p. 59)

600604-10

Main work

–

Remove protection covers

1

.

600605-10

–

Remove a defective main fuse

2

with needle nose pliers.

–

Install a new main fuse.

Fuse (58011109130) (

p. 176)

Info

A reserve fuse

3

is located in the starter relay.

–

Check the functioning of the electrical equipment.

–

Mount the protection covers.

Finishing work

–

Mount the seat. (

p. 60)

–

Set the clock. (

p. 94)

13.8

Changing fuses of individual power consumers

Info

The fuse box containing the fuses of individual power consumers is located under the seat.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the seat. (

p. 59)

600604-11

Main work

–

Open fuse box cover

1

.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands