KTM 2011 690 SMC AUS Repair Manual Download Page 108

Page: 108 / 229

ENGINE

106

–

Check the engine for leakage.

–

Check the engine oil level. (

p. 164)

–

Check the coolant level. (

p. 163)

16.3

Engine disassembly

16.3.1

Clamping the engine into the engine assembly stand

300144-10

–

Mount special tool

on engine assembly stand

Engine assembly stand (61229001000) (

p. 213)

Support for engine assembly stand (75012001060) (

p. 214)

Holder for engine assembly stand (75012001070) (

p. 214)

–

Mount the engine on special tool

Info

Have an assistant help you or use a crane.

16.3.2

Draining the engine oil

300002-10

–

Remove the oil drain plug

with the magnet and seal ring.

–

Remove plug

with oil screen and the O-rings.

300161-10

–

Remove plug

with oil screen

and the O-rings.

–

Completely drain the engine oil.

16.3.3

Removing starter motor

300001-01

–

Remove screws

. Take off the starter motor.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Brands by name

Popular brands