manualshive.com logo in svg

KTM 2011 690 SMC AUS, Repair Manual

Share
Download
KTM 2011 690 SMC AUS Repair Manual Download Page 63

11

FUEL TANK, SEAT, TRIM

61

302037-10

–

Press on the metal plate and disconnect the fuel hose connection

1

.

Info

Remaining fuel may run out of the fuel hose.

0

0

3

3

0

0

2

2

400926-10

–

Mount special tool

2

.

Pressure testing tool (61029094000) (

p. 213)

–

Mount special tool

3

with nozzle code

0,60

.

Testing hose (61029093000) (

p. 213)

–

Insert the hose end in a fuel canister.
Guideline

Minimum fuel canister capacity

10 l (2.6 US gal)

–

Perform the

"Actuator Test"

>

"Function test of fuel pump control"

.

Guideline

Maximum duration of actuator test

3 min

400927-01

–

Check the fuel pressure with the filler cap closed.

Fuel pressure

When the fuel pump is active

3.3… 3.7 bar (48… 54 psi)

» If the specification is not reached:

–

Open the filler cap. (

p. 59)

–

Check the fuel tank breather.

400928-01

–

Check the fuel pressure with the filler cap open.

Fuel pressure

When the fuel pump is active

3.3… 3.7 bar (48… 54 psi)

» If the specification is not reached:

–

Check that the fuel line is clear.

–

Change the fuel filter. (

p. 61)

–

Change the fuel pump. (

p. 64)

–

Stop the

"Function test of fuel pump control"

actuator test by pressing the

"Quit"

but-

ton.

–

Dismantle the special tools.

–

Connect the fuel hose connection.

11.8

Changing the fuel filter

Danger

Fire hazard

 

Fuel is highly flammable.

–

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–

The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

 

Fuel is poisonous and a health hazard.

–

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with
soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel.
Store fuel properly in a suitable canister and keep away from children.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands