KTM 2011 690 SMC AUS Repair Manual Download

Page: 22 / 229

FORK, TRIPLE CLAMP

200661-01

–

Release the fork leg and clamp it with the axle clamp.

Info

Use soft jaws.

200646-12

–

Push the outer tube downward.

–

Pull the spring downwards. Mount the special tool on the hexagon.

Open-end wrench (T14032) (

p. 221)

Info

The preload spacers

should be above the special tool.

200647-12

–

Clamp the special tool in the vise. Loosen screw cover

200648-12

–

Remove screw cover

with preload spacers

–

Remove adjusting tube

200649-01

–

Pull the spring downward. Remove the special tool.

–

Remove the spring.

200650-01

–

Drain the fork oil.

Info

Pull out and push in the piston rod a few times to empty the cartridge.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands