manualshive.com logo in svg

KTM 2011 690 SMC AUS, Repair Manual

Share
Download
KTM 2011 690 SMC AUS Repair Manual Download Page 40

8

SHOCK ABSORBER, SWINGARM

38

8.11

Servicing the shock absorber

Caution

Danger of accidents

 

Disassembly of pressurized parts can lead to injury.

–

The shock absorber is filled with high density nitrogen. Adhere to the description provided.

Condition

The shock absorber has been removed.

201289-01

–

Remove the spring. (

p. 38)

–

Dismantle the damper. (

p. 39)

–

Disassemble the piston rod. (

p. 40)

–

Check the damper. (

p. 41)

–

Remove the heim joint. (

p. 42)

–

Install the heim joint. (

p. 43)

–

Assemble the piston rod. (

p. 44)

–

Assemble the damper. (

p. 45)

–

Install the spring. (

p. 50)

8.12

Removing the spring

Condition

The shock absorber has been removed.

201271-10

–

Clamp the shock absorber in the vise using soft jaws for protection.

–

Measure and note spring length in preloaded state.

–

Loosen retaining ring

1

and the adjusting ring with the special tool.

Hook wrench (T106S) (

p. 219)

–

Turn the retaining ring and adjusting ring until the spring is fully relieved of ten-
sion.

201272-10

–

Remove spring retainer

2

.

–

Take off spring

3

with the retaining ring and adjusting ring

4

.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands