manualshive.com logo in svg

KTM 2011 690 SMC AUS, Repair Manual

Share
Download
KTM 2011 690 SMC AUS Repair Manual Download Page 169

19

LUBRICATION SYSTEM

167

100201-01

–

Thoroughly clean the oil drain plug with a magnet.

–

Mount the oil drain plug with the magnet and seal ring and tighten it.
Guideline

Oil drain plug with magnet

M12x1.5

20 Nm
(14.8 lbf ft)

19.6

Removing the oil filter

Warning

Danger of scalding

 

Engine oil and gear oil get very hot when the motorcycle is ridden.

–

Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Preparatory work

–

Place a suitable container under the engine.

100202-10

Main work

–

Remove screws

1

. Remove the oil filter cover

2

with the O-ring.

–

Pull oil filter

3

out of the oil filter housing.

Circlip pliers reverse (51012011000) (

p. 210)

100203-10

–

Remove screws

4

. Take off the oil filter cover

5

with the O-ring.

–

Pull oil filter

6

out of the oil filter housing.

Circlip pliers reverse (51012011000) (

p. 210)

–

Completely drain the engine oil.

–

Thoroughly clean the parts and sealing area.

19.7

Installing the oil filter

100204-10

–

Insert oil filters

1

and

2

.

–

Oil the O-rings of the oil filter covers. Mount oil filter covers

3

and

4

.

–

Mount and tighten the screws.
Guideline

Screw, oil filter cover

M5

6 Nm (4.4 lbf ft)

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands