manualshive.com logo in svg

KTM 2011 690 SMC AUS, Repair Manual

The KTM 2011 690 SMC AUS Owner's Manual is a vital resource for any rider. Navigate your way through maintenance, troubleshooting, and safety instructions with this comprehensive manual. This manual is available for free download from manualshive.com, allowing you to access it conveniently whenever needed.

Share
Download
background image

15

LIGHTING SYSTEM, INSTRUMENTS

95

400841-01

–

Switch on the ignition by turning the ignition key to position

ON

.

–

Press the

MODE

button repeatedly until the

TRIP 2

mode is active.

–

Keep the

SET

button pressed.

The

TRIP 2

display is set to

0.0

.

15.1.5

Setting the wheel circumference

Danger

Voiding of the government approval for road use and the insurance coverage

 

The vehicle is only authorized for operation on pub-

lic roads in the homologated version.

–

If the vehicle is modified in any way, it may only be used on designated tracks away from public roads. Advise the vehicle
owner and rider of this.

–

If you undertake any modifications, please insist on receiving a signed workshop order from your customer in which you
inform the customer in writing that these modifications are performed at the customer's own risk and that the vehicle will
no longer be approved for use on public roads once modified.

Condition

The motorcycle is stationary.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the headlight mask with the headlight. (

p. 96)

302064-10

Main work

–

Unplug connector

ED

from the combination instrument.

–

Unlock pin

18

A

and remove it from connector

ED

.

–

Plug connector

ED

into the combination instrument.

–

Switch on the ignition by turning the ignition key to position

ON

.

–

Press the

MODE

button repeatedly until the

TRIP 1

display mode is active.

–

Press and hold the

MODE

button for 10 seconds.

The wheel circumference is displayed in millimeters.

302053-10

Increasing the wheel circumference

–

Press the

MODE

button

1

.

Reducing the wheel circumference

–

Press the

SET

button

2

.

–

Keep the

MODE

button and the

SET

button pressed simultaneously.

The settings are saved and the Setup menu is closed.

–

Switch off the ignition by turning the ignition key to position

OFF

.

–

Unplug connector

ED

from the combination instrument.

–

Connect pin

18

to connector

ED

.

–

Plug connector

ED

into the combination instrument.

Finishing work

–

Install the headlight mask with the headlight. (

p. 97)

–

Check the headlight setting. (

p. 96)

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Related manuals for 2011 690 SMC AUS

Bajaj Pulsar 150 DTS-i User Manual preview
Pulsar 150 DTS-i
Brand: Bajaj Pages: 33
Baja motorsports DR125 Owner'S Manual preview
DR125
Brand: Baja motorsports Pages: 37
Bajaj Dominar 250 BS VI Owner'S Manual preview
Dominar 250 BS VI
Brand: Bajaj Pages: 52
Baja motorsports DB30 Mini Bike Service Bulletin preview
DB30 Mini Bike
Brand: Baja motorsports Pages: 4
Bajaj Auto Dominar 400 Owner'S Manual preview
Dominar 400
Brand: Bajaj Auto Pages: 40
Yamaha YZ450F(V) Owner'S Service Manual preview
YZ450F(V)
Brand: Yamaha Pages: 650
Yamaha TTR90(M) Owner'S Service Manual preview
TTR90(M)
Brand: Yamaha Pages: 287
Razor Rebellion Electric Chopper 15130760 Owner'S Manual preview
Rebellion Electric Chopper 15130760
Brand: Razor Pages: 17
Braaap CRUISER400 User Manual preview
CRUISER400
Brand: Braaap Pages: 40
Big Dog 2006 Chopper Owner'S Manual preview
2006 Chopper
Brand: Big Dog Pages: 100
RPS Falcon 200 Owner'S Manual preview
Falcon 200
Brand: RPS Pages: 28
Sachs Bikes MadAss 125 Owner'S Manual preview
MadAss 125
Brand: Sachs Bikes Pages: 84
Memphis Shades MEB8975 Mounting Instructions preview
MEB8975
Brand: Memphis Shades Pages: 2
DYNATEK DDK2-8 Installation & User Manual preview
DDK2-8
Brand: DYNATEK Pages: 11
DYNATEK D3K7-3 Installation Instructions preview
D3K7-3
Brand: DYNATEK Pages: 4
DYNATEK D3K3-1 Installation Instructions preview
D3K3-1
Brand: DYNATEK Pages: 4
hepco & becker 6304553 00 05 Mounting Instructions preview
6304553 00 05
Brand: hepco & becker Pages: 2
hepco & becker 5049515 00 05 Quick Start Manual preview
5049515 00 05
Brand: hepco & becker Pages: 3

Brands by name

Popular brands

Load more brands