manualshive.com logo in svg

KTM 2011 690 SMC AUS, Repair Manual

The KTM 2011 690 SMC AUS Owner's Manual is a vital resource for any rider. Navigate your way through maintenance, troubleshooting, and safety instructions with this comprehensive manual. This manual is available for free download from manualshive.com, allowing you to access it conveniently whenever needed.

Share
Download
background image

14

BRAKE SYSTEM

91

14.10

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

 

Brake system failure.

–

If there is no free travel on the foot brake lever, pressure builds up on the rear brake circuit. The rear brake can fail due to
overheating. Adjust the free travel on foot brake lever according to specifications.

B01291-10

–

Loosen fitting

3

on foot brake cylinder

4

.

–

To adjust the basic position of the foot brake lever individually, loosen nut

1

and

turn screw

2

accordingly.

Info

The range of adjustment is limited. The screw must be screwed into the
footrest bracket by at least four turns.

–

Position foot brake cylinder

4

so that the foot brake lever has the necessary free

travel. Hold screws

3

in place and tighten the nuts.

Guideline

Screw connection, foot brake cylinder

M6

10 Nm (7.4 lbf ft)

–

Check the free travel of the foot brake lever. (

p. 90)

–

Tighten nut

1

.

14.11

Checking rear brake fluid level

Warning

Danger of accidents

 

Failure of the brake system.

–

If the brake fluid level falls below the

MIN

mark, this indicates a leakage in the brake system or worn-out brake linings.

Check the brake system and do not continue riding.

Warning

Danger of accidents

 

Reduced braking efficiency due to old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule.

100258-10

–

Stand the vehicle upright.

–

Check the brake fluid level in the brake fluid reservoir.
» If the fluid level reaches the

MIN

marking

1

:

–

Add rear brake fluid. (

p. 92)

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Reviews:

No comments

Related manuals for 2011 690 SMC AUS

Fantic Motor 125 Series Owner'S Manual preview
125 Series
Brand: Fantic Motor Pages: 130
Tao Motor TBR7 Installation Manual preview
TBR7
Brand: Tao Motor Pages: 3
ZARD ZUMA Fitting Manual preview
ZUMA
Brand: ZARD Pages: 2
Öhlins YA812 Mounting Instructions preview
YA812
Brand: Öhlins Pages: 2
Öhlins YA 314 Mounting Instructions preview
YA 314
Brand: Öhlins Pages: 2
Öhlins TR 538 Mounting Instructions preview
TR 538
Brand: Öhlins Pages: 2
Öhlins ST44 Mounting Instructions preview
ST44
Brand: Öhlins Pages: 2
Öhlins SD195 Mounting Instruction preview
SD195
Brand: Öhlins Pages: 2
Öhlins SD 168 Mounting Instructions preview
SD 168
Brand: Öhlins Pages: 2
Öhlins SD 154 Mounting Instructions preview
SD 154
Brand: Öhlins Pages: 2
Öhlins RS 562 Mounting Instructions preview
RS 562
Brand: Öhlins Pages: 2
Öhlins POF5H00 Mounting Instructions preview
POF5H00
Brand: Öhlins Pages: 2
hepco & becker 501546 00 01 Manual preview
501546 00 01
Brand: hepco & becker Pages: 5
Contracor COMFORT 10130810 Instructions Manual preview
COMFORT 10130810
Brand: Contracor Pages: 36
Ohlins FGR 156 Mounting Instructions preview
FGR 156
Brand: Ohlins Pages: 8
klicbag 8983K Mounting Instructions preview
8983K
Brand: klicbag Pages: 2
KTM 50 SX 2015 Setup Instructions preview
50 SX 2015
Brand: KTM Pages: 13
KTM 85 SX 2003 Owner'S Manual preview
85 SX 2003
Brand: KTM Pages: 38

Brands by name

Popular brands

Load more brands