KTM 2011 690 SMC AUS Repair Manual Download

Page: 48 / 229

SHOCK ABSORBER, SWINGARM

201278-11

–

Grease O-ring

of the seal ring retainer.

Lubricant (T158) (

p. 208)

–

Mount the piston rod carefully.

201276-10

–

Install the seal ring bearer

and push it under the ring groove.

–

Mount lock ring

Info

Do not scratch the inner surface.

–

Pull out the piston rod so that the seal ring retainer rests against the lock ring.

201275-10

–

Mount locking cap

of the damper cartridge.

–

Bleed and fill the damper. (

p. 47)

–

Fill the damper with nitrogen. (

p. 49)

201287-10

Alternative 1

–

Turn adjusting screw

clockwise with a screwdriver up to the last perceptible

click.

–

Turn back counterclockwise by the number of clicks corresponding to the shock
absorber type.
Guideline

Compression damping, low-speed

Comfort

20 clicks

Standard

15 clicks

Sport

10 clicks

Full payload

10 clicks

–

Turn adjusting screw

all the way clockwise using a socket wrench.

–

Turn back counterclockwise the number of turns corresponding to the shock
absorber type.
Guideline

Compression damping, high-speed

Comfort

1.5 turns

Standard

1 turn

Sport

0.5 turn

Full payload

0.5 turn

–

Turn adjusting screw

clockwise up to the last perceptible click.

–

Turn back counterclockwise by the number of clicks corresponding to the shock
absorber type.

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands