KTM 2011 690 SMC AUS Repair Manual Download

Page: 158 / 229

ENGINE

156

300012-12

–

Put on the water pump cover

. Mount and tighten screws.

Guideline

Screw, water pump cover

10 Nm (7.4 lbf ft)

16.5.27 Installing thermostat

300010-11

–

Position the thermostat

with the gasket.

The drill hole

must face upward.

–

Install the thermostat case

with the radiator hose.

–

Mount and tighten the screws.
Guideline

Screw, thermostat housing

10 Nm
(7.4 lbf ft)

Loctite

243™

16.5.28 Installing the oil filter

300009-11

–

Insert the oil filter

–

Lubricate the O-ring of the oil filter cover. Install the oil filter cover

–

Mount and tighten the screws.
Guideline

Screw, oil filter cover

6 Nm (4.4 lbf ft)

300011-11

–

Insert the oil filter

–

Lubricate the O-ring of the oil filter cover. Install the oil filter cover

–

Mount and tighten the screws.
Guideline

Screw, oil filter cover

6 Nm (4.4 lbf ft)

16.5.29 Installing gear position sensor

300007-11

–

Mount the contact springs

and contact bolt

The contact bolts are mounted with the flat side forward; the pointed sides
face the sensor.

–

Position O-ring

Summary of Contents for 2011 690 SMC AUS






































































































































































































































Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands

KTM 2011 690 SMC AUS, Repair Manual

Search results

Summary of Contents for 2011 690 SMC AUS

Reviews:

Related manuals for 2011 690 SMC AUS

Brands by name

Popular brands