Konica Minolta DRYPRO Model 793 Operation Manual Download Page 98

Page: 98 / 156

Ch.4 Maintenance Mode

< 96 >

DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1

Insert the cleaning sheet parallel to the roller

surface between the Cleaning Roller and the

Facing Roller. (4 in the left fig)

Insert the cleaning sheet always parallel to

the Cleaning Roller.

As shown in the fig, move the Lever up and

down while holding the top edge of the cleaning

sheet with a hand.

- Cleaning sheet will be sent through between the Cleaning

Roller and the Facing Roller.

Repeat the step 6 through 9 to send the cleaning

sheet several times between the rollers when

necessary.

Be careful not to drop the cleaning film into

the main unit.

Switch your hand to hold the other edge of the

cleaning sheet when it comes out between the

Cleaning Roller and Facing Roller, and push the

Lever up and down with your right hand to send

the cleaning sheet through.

Do not pull the cleaning sheet forcefully. Send it thorough the rollers until it com-

pletely comes out only by pushing the Lever.

Summary of Contents for DRYPRO Model 793





























































































































































Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands

Konica Minolta DRYPRO Model 793, Operation Manual

Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands