Konica Minolta DRYPRO Model 793 Operation Manual Download Page 139

Page: 139 / 156

Ch.6 Troubleshooting

< 137 >

DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1

Close the Right Cover.

Close the Jam Release Cover-C, and the Front

Bottom Cover by hand.

- "READY" will be displayed in the message column

when the jam release sequence is completed, and the
DRYPRO 793 becomes ready to print.

Animation of Jam
Release in the Elevator
Transport Unit.

Open the Jam Release Cover-C (1 in the left

fig.), and send the jam film to the left.

- The film sent to the left can now be located through the

opening of the Right Cover.

Pull out the film jammed in the Elevator Trans-

port Unit.

Do not pull out the jam film through the Jam Release Cover.

Summary of Contents for DRYPRO Model 793





























































































































































Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands

Konica Minolta DRYPRO Model 793, Operation Manual

Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands