Konica Minolta DRYPRO Model 793 Operation Manual Download Page 146

Page: 146 / 156

Ch.7 Care & Maintenance

< 144 >

DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1

Slide the Deodorant Filter Cover to the right. (1 in

the left fig.)

- The Deodorant Filter Cover will be locked.

When failed to install the Deodorant Filter Case or forgot install it, a message "FIL-

TER EXCHANGE" will be displayed again. Touch the [FILTER EXCHANGE] button

and install the Deodorant Filter Case.

Install the new Deodorant Filter.

- As shown in the figure, insert the Deodorant Filter deep

enough with the handle to the front and the holes on the
cardboard to the top.

Close the Deodorant Filter Cover. (2 in the left

fig.)

Close the Front Top Cover.

- "READY" will be displayed in the message column, and

the DRYPRO 793 becomes ready to print.

Turn the Lever-A clockwise. (2 in the left fig.)

- The Deodorant Filter Case will be locked to the

DRYPRO 793.

Animation of Deodorant
Filter Change 2-(2)

Animation of Deodorant
Filter Change 3

Prepare a new Deodorant Filter.

Summary of Contents for DRYPRO Model 793





























































































































































Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands

Konica Minolta DRYPRO Model 793, Operation Manual

Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands