Konica Minolta DRYPRO Model 793 Operation Manual Download Page 138

Page: 138 / 156

Ch.6 Troubleshooting

< 136 >

DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1

6-3-3 Film Jam in the Elevator Transport Unit

Error codes "4511", "4610", "4620", "4621" indicate the jam in the Elevator Transport Unit.
Remove the jam film according to the following procedure.

Touch the [ERROR RESET] button.

- Front Bottom Cover opens.

- An animation showing the jam release procedures will

be displayed on the Operation Panel.

Press the Lever-C, and open the Right Cover.

Animation of Jam
Release in the Elevator
Transport Unit.

When the jam film is located,pull it out by hand.

- When the removal of the jam film was successful, pro-

ceed to the step 6.

- When the jam film cannot be located, proceed to the

step 4.

Summary of Contents for DRYPRO Model 793





























































































































































Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands

Konica Minolta DRYPRO Model 793, Operation Manual

Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands