Konica Minolta DRYPRO Model 793 Operation Manual Download Page 136

Page: 136 / 156

Ch.6 Troubleshooting

< 134 >

DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1

Press the Lever-C, and open the Right Cover.

When the jam film is located,pull it out by hand.

- When the removal of the jam film was successful, pro-

ceed to the step 6.

- When the jam film cannot be located, proceed to the

step 4.

Open the Jam Release Cover-C (1 in the left

fig.), and send the jam film to the left.

- The film sent to the left can now be located through the

opening of the Right Cover.

Pull out the film jammed in the Elevator Trans-

port Unit.

Do not pull out the jam film through the Jam Release Cover.

Close the Jam Release Cover-C.

Close the Right Cover.

Animation of Jam
Release in the Descent
Transport Unit. 4

Animation of Jam
Release in the Descent
Transport Unit. 5

Summary of Contents for DRYPRO Model 793





























































































































































Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands

Konica Minolta DRYPRO Model 793, Operation Manual

Search results

Summary of Contents for DRYPRO Model 793

Reviews:

Related manuals for DRYPRO Model 793

Brands by name

Popular brands