Kimberley KARAVAN 2021 Installation, Maintenance & Operating Manual Download Page 58

Page: 58 / 120

Features | Multi-media System

Portable TV Screen (Optional)

Karavans can be supplied with a flat screen TV.

NOTE:

TV cannot be left on canopy mount when lowering canopy and travelling. Please remove and place in provided

bag and secure to the back of the seat. For more detailed information about using the TV see the ‘Operating

Instructions’ in Owner’s Satchel.

You can eqip your caravan with a Satellite TV system for TV reception almost

anywhere in Australia. An automatic satellite receiver dish is mounted to the roof of

the Karavan. A control panel and VAST decoder box are installed in the front of the

canopy for easy access.

How to use your satellite TV

1. Ensure Canopy power is ON at the dash panel.

2. Press the “Power” button on the control panel - the satellite dish will raise up and

rotate to search for a satellite. When satellite found “Satellite Found” will display on

the control panel.

To finish using, press the “Power” button again and dish will lower ready for travel.

NOTE:

Ensure Satellite dish is lowered before any travel.

Access to the VAST satellite service is managed by a smart card which is supplied

with the satellite set top box. To access VAST you will need to register your details

including your address, reception location and smart card number to enable access.

For more information visit: https://www.myvast.com.au/register

For more nformation about using the satellite TV see the “Operating Instructions Manual” in Owner’s Satchel.

If the Satellite Won’t Go Down...

1. Disconnect cables from the control box (in the media console)

2. Undo screws and remove control box

3. Then remove the 4x small Allen key screws & the cover.

4. On the circuit board you will see the fuse and fuse holder

5. Replace fuse

Features | Satellite TV (Optional)

Summary of Contents for KARAVAN 2021

























































































































Search results

Summary of Contents for KARAVAN 2021

Reviews:

Related manuals for KARAVAN 2021

Brands by name

Popular brands

Kimberley KARAVAN 2021, Installation, Maintenance & Operating Manual

Search results

Summary of Contents for KARAVAN 2021

Reviews:

Related manuals for KARAVAN 2021

Brands by name

Popular brands