Kimberley KARAVAN 2021 Installation, Maintenance & Operating Manual Download Page 30

Page: 30 / 120

WiTi Wireless Trailer Plug Connection with built-in Anti-theft & GPS tracking (Optional)

OPERATION GUIDE

WiTi

Wireless Towing Interface replaces the traditional cables between a tow vehicle and caravan / trailer

with an advanced wireless connection.

WiTi

transmits all lighting and braking signals using the latest WiFi

technologies for fast, secure and stable communication. Although wireless,

WiTi

is not dependant upon

the Internet and communication is point to point between the vehicle unit and trailer unit. The signal is also

encrypted for security and other wireless devices will not interfere with the

WiTi

Wireless Towing Interface

(mobile phones, bluetooth, wifi devices, etc.)

No more cables to damage or rip out, no more corroded terminals and no more loose connections.

Low Power Mode

WiTi

Wireless Towing Interface will enter low power mode if there is inactivity for 24 hours. In this mode power

draw is less than 2 milliAmps.

WiTi

will exit Low Power Mode when it detects an input from the driving light

circuit.

CanBus and vehicles fi tted with advanced towing features

WiTi

Wireless Towing Interface supports all CanBus vehicles and vehicles with advanced electronics.

WiTi

supports vehicle specifi c towing modes and features for example, disabling reverse sensors when hitched.

These features will be enabled when the

WiTi

Wireless Towing Interface is in range and paired with the

WiTi

Anti Theft unit in the caravan or trailer. Please refer to your vehicle hand book for vehicle specifi c towing

modes.

WiTi

supports towing modes for:

• Dodge RAM

• Ford vehicles including F Series Trucks

• Isuzu

• Jeep

• Mitsubishi

• Nissan

• Toyota

• VW (Including Amarok and Toureg)

Supported Brake Controllers

WiTi supports all modern electric brake controllers including factory fi tted units on imported vehicles such as

Ford F Series and Dodge RAM.

If a

WiTi

Wireless Electric Brake Controller is installed then signals from wired brake controllers (pin 5) will be

ignored.

Summary of Contents for KARAVAN 2021

























































































































Search results

Summary of Contents for KARAVAN 2021

Reviews:

Related manuals for KARAVAN 2021

Brands by name

Popular brands

Kimberley KARAVAN 2021, Installation, Maintenance & Operating Manual

Search results

Summary of Contents for KARAVAN 2021

Reviews:

Related manuals for KARAVAN 2021

Brands by name

Popular brands