Kimberley KARAVAN 2021 Installation, Maintenance & Operating Manual Download Page 118

Page: 118 / 120

118

Seating Fabric Cleaning Guide and Care

Spot cleaning

Treat spills and stains as soon as possible. Test

on hidden area to ensure fabric and colour are

not removed. Gently scrape any soil or mop any

liquid from the surface of the fabric. Use of soap

or detergent with water should be approached with

caution since overzealous rinsing to remove soap

residue may result in over-wetting, water marking

and possible wetting of substructure (this may create

other stains or damage

products).

1. For non-oil-based stains.

Use warm water and

non-toilet soaps which do not contain optical

brighteners (consider Velvet soap, Lux Flakes,

Softly). Mix a small amount of soap and warm

water solution and apply to the stain, rubbing

gently. Blot dry with a clean towel. Apply cool

water (preferably fi ltered or distilled water) and

blot dry again. Then with a hair dryer, working out

from the centre of the stain, dry quickly to prevent

rings forming. It is generally preferable to clean

whole panels of fabric in this way rather than

trying to spot clean specifi c areas.

2. For oil-based stains

. Following the same basic

guidelines as above, apply a proprietary brand

solvent based cleaner and try to clean generally

in panels rather than spot cleaning specifi c

areas. A helpful industry ‘secret’ for spot removal

of oil based biro marks is by the application of

conventional hair spray. To further enhance spot

cleaning results, Warwick have introduced the

Halo Fabric Care Kit which includes Halo spot

cleaner for most household stains, Halo fabric

deodoriser to help neutralise pet and general

odours and Halo fabric protector to restore liquid

repellency on fabric sections that have been spot

cleaned.

*For treatment of specifi c stains, see the stain

removal guide.

Professional fabric servicing

Warwick Fabrics recommend that water-based

‘Fluro chemical’ type fabric protectors (such as

DuPont Tefl on® and 3M Scotchgard®) be applied by

licensed applicators only. Check your care label fi rst

to see if a mill-applied protection was incorporated

during fabric manufacture. Fabric protectors do not

eliminate the need for vacuuming, routine cleaning or

proper care. They will, however, make spot cleaning

and vacuuming quicker, easier and more effi cient

between professional cleans and keep your fabric

looking cleaner longer, as well as extending its life.

Professionals applying fabric protectors must always

pre-test to qualify fabric suitability.

Warning

Extreme caution should be taken if considering

treatment of velvets and pocket weaves with stain

repellent products. Some high pile velvet and pocket

weave jacquards may change in surface character

if stain repellent treatments are incorrectly applied.

Extra care should be taken to pre-test for these

fabrics.

Professional cleaning frequency

Is determined by the furniture use, your own

maintenance, upkeep and environmental conditions.

As a good ‘rule of thumb’ overall cleaning is

recommended every 12 months for most family room

lounges.

Summary of Contents for KARAVAN 2021

























































































































Search results

Summary of Contents for KARAVAN 2021

Reviews:

Related manuals for KARAVAN 2021

Brands by name

Popular brands

Kimberley KARAVAN 2021, Installation, Maintenance & Operating Manual

Search results

Summary of Contents for KARAVAN 2021

Reviews:

Related manuals for KARAVAN 2021

Brands by name

Popular brands