Keysight Technologies N7020A User Manual Download Page 16

Page: 16 / 92

N7020A and N7024A Power Rail Probes User’s Guide

N7020A / N7024A Probes - Overview

Oscilloscope Compatibility

The N7020A and N7024A probes are compatible with the Keysight oscilloscopes

shown in

Table 3

and

Table 4

. The tables also list the minimum required firmware

version to support these probes.

Table 4

Compatible Oscilloscopes for the N7024A Probe

NOTE

The N7020A and N7024A probes are designed for Keysight oscilloscopes with 50

AutoProbe-interface channel inputs.

Table 3

Compatible Oscilloscopes for the N7020A Probe

Oscilloscopes

Required

Firmware Version

S-Series

≥

5.20

9000 Series

≥

5.20

9000A

≥

5.20

6000 X-Series

≥

6.10

4000 X-Series

≥

4.00

3000T X-Series

≥

4.00

3000A-X-Series

≥

2.39

Infiniium Oscilloscopes

Required

Firmware Version

S-Series

≥

06.20.00803

V-Series

(with N5442A adapter)

Z-Series

(with N5442A adapter)

Summary of Contents for N7020A





























































































Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands

Keysight Technologies N7020A, User Manual

Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands