Keysight Technologies N7020A User Manual Download Page 81

Page: 81 / 92

Performance Verification

N7020A and N7024A Power Rail Probes User’s Guide

Bandwidth Performance Verification for N7024A Probe

This section provides information to test that the N7024A probe meets its

warranted bandwidth specification, which is 6 GHz. As the warranted specification

is just for the N7024A probe, this performance verification procedure verifies the

bandwidth of just the N7024A probe without its N7022A main cable.

Procedure for Verifying Bandwidth Specification (for the N7024A Probe

Only)

Power on the oscilloscope.

Choose

Control

Default Setup

or press the

[Default Setup]

key on the front panel of

the oscilloscope to configure the oscilloscope to its default settings.

Connect one end of the calibration coax cable to one of the input channels of the

oscilloscope.

Table 15

Required Test Equipment

Test Equipment

Critical Specification

Keysight Model Number

Infiniium Oscilloscope

Supported oscilloscope with bandwidth >= 8

GHz

Refer to the

Table 4

to get a list

of supported oscilloscopes.

Precision BNC Adapter

If V or Z-series Infiniium oscilloscope (with

AutoProbe 2 inputs) is being used

N5442A

Precision BNC (M) to SMA (F) Adapter

If S-series Infiniium oscilloscope (with

AutoProbe 1 inputs) is being used

54855-67604

Calibration Coaxial Cable

The calibration cable that accompanies the

oscilloscope

A high quality 3.5mm or 2.92mm coax cable

Example - 54916-61626

Adapters to connect the coax cable to Cal

Out and channel input on the oscilloscope

SMA f-f adapters that accompany the

oscilloscope

3.5mm or 2.92mm SMA f-f adapters

Example - 54916-68716

NOTE

Before starting the performance verification, allow the oscilloscope to

warm up for at least 20 minutes.

Summary of Contents for N7020A





























































































Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands

Keysight Technologies N7020A, User Manual

Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands