Keysight Technologies N7020A User Manual Download Page 85

Page: 85 / 92

Performance Verification

N7020A and N7024A Power Rail Probes User’s Guide

Check the frequency response of the N7024A probe. To do this, perform the

following steps.

Disconnect the calibration coax cable and any adapters that you attached to

the input channel of the oscilloscope.

Connect the N7024A probe to the input channel and calibration coax cable.

You may need to use the N5442A adapter with the probe in case you are

using a V-series or a Z-series oscilloscope.

Figure 31

Calibration setup with the N7024A probe and calibration cable

Choose

Setup

Probe Configuration...

Select the tab of the oscilloscope’s input channel to which the probe is

connected.

In the

Probe Head

block, click

Select Head...

. Select

Generic:User Cable

configure the oscilloscope to not consider any loss from the N7022A main

cable or any probe browsers. Click

and close the dialog.

Calibration

Cable

SMA f-f

Adapter

N7024A

Probe

N5422A

Adapter

Summary of Contents for N7020A





























































































Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands

Keysight Technologies N7020A, User Manual

Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands