Keysight Technologies N7020A User Manual Download Page 86

Page: 86 / 92

N7020A and N7024A Power Rail Probes User’s Guide

Performance Verification

Set the channel offset for the oscilloscope to

-640mV

and the trigger level to

-640mV

as displayed in

Figure 32

The f2 trace now has the frequency response with the N7024A probe

attached. The already saved and displayed memory 1 trace has the

frequency response of the coax cable. For comparison, grab the f2 trace and

align it with the memory 1 trace, if needed as displayed in

Figure 32

The frequency response of the N7014A probe is the difference between the

f2 trace and memory 1 trace. Verify whether or not this difference is less

than

3db

at 6 GHz or below. If it is less, then the probe passes the test.

Notice that in the figure below, the N7024A probe passed the bandwidth

verification test as the frequency response of the probe s not above 3db at 6

GHz or below.

Figure 32

Frequency response of the N7024A probe

Summary of Contents for N7020A





























































































Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands

Keysight Technologies N7020A, User Manual

Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands