Keysight Technologies N7020A User Manual Download Page 84

Page: 84 / 92

N7020A and N7024A Power Rail Probes User’s Guide

Performance Verification

Record and save the frequency response of the Cal Out step through the attached

calibration coax cable. To do this, perform the following steps.

The f2 trace is displayed at the bottom of the screen. Drag the f2 trace to the

center graticule.

Save the frequency response of the coax cable by right-clicking the f2 trace

and saving it to

memory 1

. This will allow you to later compare the saved

frequency response of the Cal Out step through the attached calibration

coax cable with the frequency response of the N7024A probe (done in steps

that follow).

For ease of comparison, drag the memory 1 trace into the same window as

the f2 trace. Close the window that was initially displayed for memory 1.

Figure 30

Frequency response of the Cal Out step through the attached coax cable

Summary of Contents for N7020A





























































































Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands

Keysight Technologies N7020A, User Manual

Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands