Keysight Technologies N7020A User Manual Download Page 59

Page: 59 / 92

Calibrating

N7020A and N7024A Power Rail Probes User’s Guide

N7020A / N7024A Probe’s DC Attenuation/Offset Calibration Using

N7023A Probe Browser

Turn on the oscilloscope and connect the N7023A power rail probe browser with

the N7020A / N7024A probe attached to one of the oscilloscope’s input channels.

Allow the oscilloscope to warm up for 20 minutes.

If the oscilloscope needs calibration, perform a user calibration before the probe

calibration. On the oscilloscope, click

Utilities

Calibration

Connect the ground lugs and the output of the N7023A power rail probe browser

to the oscilloscope’s front-panel PROBE COMP connector.

On the oscilloscope, click

Setup

Probes

In the Probe Calibration dialog box, select the tab representing the channel that

has the probe attached.

In the dialog box, select the type of calibration. Click

Start

and follow the

instructions shown on the oscilloscope.

Summary of Contents for N7020A





























































































Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands

Keysight Technologies N7020A, User Manual

Search results

Summary of Contents for N7020A

Reviews:

Related manuals for N7020A

Brands by name

Popular brands