manualshive.com logo in svg

Keysight Technologies N7020A, User Manual

Share
Download
Keysight Technologies N7020A User Manual Download Page 7

N7020A / N7024A Probes - Overview

1

N7020A and N7024A  Power Rail Probes User’s Guide

7

• Large active signal range in addition to the offset range

NOTE

While the N7020A and N7024A probes have a number of features in common, the N7024A 

probe is an extension to the capabilities and performance of the N7020A probe. When 

compared to the N7020A probe, the N7024A probe provides enhanced features such as:
> higher bandwidth (upto 6 GHz)
> compatibility with high-end Keysight oscilloscopes (V-series and Z-series)
> improved usability and browsing capabilities
> unique s parameters stored in each N7024A probe for maximum accuracy

CAUTION

Before using these probes, refer to 

“Safety and Regulatory Information"

on page 35. 

Handle the probes with care and refer to the safety notices in this manual. Avoid any 

mechanical shocks to these products to guarantee accurate performance and protection.

Summary of Contents for N7020A





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands