manualshive.com logo in svg

Keysight Technologies N7020A, User Manual

Share
Download
Keysight Technologies N7020A User Manual Download Page 21

General Information

2

N7020A and N7024A  Power Rail Probes User’s Guide

21

Handling the Probe

Handle the probe with care to avoid injury, especially when it is fitted with the 

extra thin and sharp spring contact tip.

CAUTION

The browser cable is a sensitive part of the N7023A power rail probe browser and, 

therefore, you should be careful not to damage it through excessive bending or pulling. 

You should also avoid any mechanical shocks to this product in order to guarantee 

accurate performance and protection.

WARNING

Periodically inspect the probe wires and cables to check for any damage. The probe 
must NOT BE USED if there are any signs of damage.

CAUTION

If the N7022A main cable is damaged, it may cause the N7024A probe to not meet its 

warranted bandwidth specification of 6 GHz. It is recommended to verify the cable using 

the procedure described in 

“To verify if the N7022A main cable is damaged"

on page 87.

Summary of Contents for N7020A





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands