manualshive.com logo in svg

Keysight Technologies N7020A, User Manual

Share
Download
Keysight Technologies N7020A User Manual Download Page 58

58

N7020A and N7024A  Power Rail Probes User’s Guide

6

Calibrating

N7020A / N7024A Probe’s DC Attenuation/Offset Calibration Using 

N7022A Main Cable

1

Turn on the oscilloscope and connect the N7020A / N7024A probe with the 

N7022A main cable attached to one of the oscilloscope’s input channels.

2

Allow the oscilloscope to warm up for 20 minutes.

3

If the oscilloscope needs calibration, perform a user calibration before the probe 

calibration. On the oscilloscope, click 

Utilities

 > 

Calibration

.

4

Connect the output of the N7022A main cable to the oscilloscope’s rear-panel 

AUX OUT BNC connector as shown in the following picture. You’ll need a BNC (m) 

to SMA (f) adapter.

Figure 14

Calibration Setup

5

On the oscilloscope, click 

Setup

 > 

Probes

.

6

In the Probe Calibration dialog box, select the tab representing the channel that 

has the probe attached.

7

In the dialog box, select the type of calibration. Click 

Start

 and follow the 

instructions shown on the oscilloscope.

Summary of Contents for N7020A





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands